When using a forklift boom, it is essential to follow the safety operating procedures to ensure the safety of personnel and extend the service life of the forklift boom.
1. Forklift boom operators must undergo specialized training, pass the relevant department's examination, and be issued a qualification certificate before being allowed to operate the equipment. Operation by unlicensed personnel is strictly prohibited.
2. Before operation, the forklift boom operator must check that all components are functioning properly, that the wire rope meets safety regulations, and that the brakes, hydraulic devices, and safety devices are complete, reliable, and sensitive. Operating the forklift boom with any malfunctioning components is strictly prohibited. When parked or moving, the distance between the wheels, the front end or outer side of the boom, and the edge of a ditch or pit must not be less than 1.2 times the depth of the ditch or pit; otherwise, anti-tipping and anti-collapse measures must be taken.
3. When lifting heavy objects, the object should first be lifted approximately 10 centimeters off the ground to check the stability of the forklift boom and the flexibility and effectiveness of the brakes. Work can only continue after confirming that everything is normal.
4. Forklift and crane operators must closely cooperate with the signalman and obey the signalman's commands. The horn must be sounded before operation. If the signal is unclear or incorrect, the driver has the right to refuse to execute it. During operation, the driver must immediately obey any emergency stop signal given by anyone.
5. Standing on the load is strictly prohibited, as is standing or passing under the load.
6. When lifting at full load, it is prohibited to use two or more operating actions simultaneously. The left and right rotation angle of the boom must not exceed 45°. Diagonal lifting, pulling, and rapid raising and lowering are strictly prohibited. Lifting or pulling objects buried in the ground is strictly prohibited, as is forcibly lifting or pulling large objects that are attached to the ground.
7. During operation, a certain distance should be maintained between the hook and the pulley to prevent the winch from exceeding its limit and breaking the cable or causing the boom to tip backward. When the boom is fully extended to its maximum elevation angle and the hook is lowered to its lowest position, at least three turns of cable should remain on the winch drum.
8. The boom angle must not be less than 30° during operation. When a load is being lifted, boom amplitude changes should be avoided as much as possible. Changing the control lever is absolutely prohibited before the load has come to a complete stop.
9. Lifting operations involving large wind-exposed areas are prohibited when the wind force at the work site reaches level 5; lifting operations are prohibited when the wind force reaches level 6 or above. During work stoppages or rest periods, the load must not be left suspended in the air.
10. Command signals must be clearly explained to the crane operator beforehand. If the command signals are unclear during operation, a relay assistant should be appointed to accurately transmit the signals.
11. Command hand gestures must be clear, and signals must be unambiguous. Gloves are not allowed to be worn while commanding. Before lifting an object, check that the binding is secure. Pads should be placed where ropes pass through sharp edges or cuts. The center of gravity of the lifting position must be accurate; the object must not twist, bend, sink, or tilt under load.
12. Before the object being lifted is in place and secured, the operator must not leave their post and must not interrupt work while the rigging is under stress or the object is suspended in the air.
13. If the operator refuses to lift due to the object being too heavy, the person in charge should take measures to reduce the overload on the crane. Forcibly directing the crane to operate beyond its load is strictly prohibited.
14. After work is completed, the hook and boom should be placed in the designated secure positions, and all control handles should be returned to the neutral position.
15. Drivers must strictly adhere to the "Ten Don'ts on Lifting":
1. Do not lift if the load is overloaded or the weight of the object is unclear;
2. Do not lift if the command signals are unclear;
3. Do not lift if the binding or hanging is insecure or unbalanced, potentially causing slippage;
4. Do not lift if there are people or loose objects on the object;
5. Do not lift if the structure or components have defects or damage that affect safe operation;
6. Do not lift if there are buried objects with unclear tension;
7. Do not lift if the work area is dark and the site, the object, and the command signals are unclear;
8. Do not lift if there is no padding between the sharp edges of the object and the binding wires;
9. Do not lift if the load is pulled at an angle;
10. Do not lift if the crane's safety devices are incomplete or unreliable, etc.
In addition to being familiar with the mechanical performance and structure, forklift crane drivers should also master the basic knowledge of loading and unloading operations:
1. On good road surfaces, the rated lifting capacity of the forklift boom is 3 tons. When operating in poor road conditions, the lifting capacity should be appropriately reduced, and the travel speed should be decreased.
2. When loading goods, adjust the boom distance according to the size of the goods. For heavier goods, extend the boom slightly beyond the load's length, lifting the goods approximately 200 mm off the ground before proceeding.
3. High-speed sharp turns, lifting or lowering goods, etc., are strictly prohibited. No one is allowed under the crane boom.
4. When transporting goods on a slope exceeding 7°, ensure the goods are on the upper side of the slope. Avoid sudden braking while transporting goods to prevent them from slipping. When moving large, obstructed cargo, reverse at low speed.
5. Never leave the engine idling unattended after stopping the crane. Never leave the driver's seat with cargo suspended in the air.
6. During operation, if any suspicious noise or abnormal phenomena are detected, stop the crane immediately for inspection and take immediate action to resolve the issue. Do not continue operation until the problem is resolved.
7. After a day's work, refuel the fuel tank. This not only removes moisture from the tank but also prevents condensation from brake air overnight from dissolving into the fuel.
8. No one may operate the forklift crane without the approval of company management. To extend its service life and prevent accidents, and to maintain the optimal operating condition of the forklift boom and the normal functioning of all parts, strict and regular maintenance must be performed on this machine during use.
Before each shift, the following must be checked:
1. Check the fuel level.
2. Check for leaks in the fuel lines, water lines, exhaust pipe, and all accessories.
3. Check that the working fuel tank capacity meets the specified requirements.
4. Check the tightness of the wheel bolts and the tire pressure to the specified values.
5. Check the flexibility and reliability of the steering and braking systems.
6. Check the electrical wiring for grounding, loose connections, and ensure the horn, turn signals, brake lights, and all instruments are functioning properly. Work can only begin after all the above preparations are completed.

